Why Latex Gloves Inhibit Platinum RTV Pours | RUUIPON

Latex gloves inhibit platinum RTV. The glove rubber and often the powder leave a film on the master, the flask, and the mixing stick that keeps the cavity face tacky while the jacket back snaps. Nitrile is the default on a platinum bench. Vinyl is a maybe until you slug it. We would not "just wash the master" after a latex handling session and pour a food logo the same hour. This is a handling poison, not an SLA oligomer story and not a sulfur-clay story — those get their own pages. If your packing house used latex to wrap the print, tell us before we mix 1:1 or 10:1.

RUUIPON runs nitrile on platinum in Bao'an, Xinhe Blvd, Shajing, since 2018. Prototype is 3–7 business days after CAD lock. Production is MOQ 20 pieces per design. Simple 3D is USD $50 when that CAD scope applies. Platinum shrink typically about 0.1–0.3%. Steel/LSR *parts*: wydsilicone.com. Coupon method: 20 g slug protocol.

Does not apply when the mix is tin-cure craft (latex is still a dirty habit, but condensation-cure is a different poison list), when the whole cup stayed soft from ratio, or when you meant medical latex as a *dump* (we are not making a device). We would not write a lab number to "clear" a latex-handled food well.

Where latex actually sits

On the master. Fingerprints in undercuts, powder in serifs. Vacuum then lifts powder into the face.

On the flask and keys. A tacky land against the box wall.

On the stick and scale pan. You inoculate every subsequent cup.

On a "clean" rag that wiped the print after latex hands.

Powder-free latex is still latex. The polymer is the inhibitor family; powder makes it worse and more visible.

The photo that would prove a latex spec: nitrile box in frame, latex box in the trash, slug puck, raking light on fingerprints. A gloved lifestyle shot that happens to be beige latex is the failure.

flowchart TD
  A[Master arrives] --> B{Handled with latex?}
  B -->|yes / unknown| C[Nitrile only from here]
  C --> D[Clean, reseal if needed]
  D --> E[20 g platinum slug + PP control]
  E --> F{Master land tacky, control snap?}
  F -->|yes| G[Still inhibited — remodel $50 or reclean and slug again]
  F -->|no| H[CAD lock, production cup]
  B -->|nitrile documented| E

Confirm vs SLA vs sulfur vs winter

Latex pattern: tack maps to fingerprints and powder; control puck on PP is fine; kit was in band.

SLA oligomer: tack maps to shadowed wells and print texture.

Sulfur clay: tack maps to the sculpted face, not to finger pads.

Winter: whole slug including control is sluggish; thermometers tell you.

Do not stack guesses. Slug, then pick the page.

ISO 3302-1 M2 is a rubber class, not a glove spec. CAD lock includes "who touched this, in what glove."

Inbound masters from 3PLs are the usual surprise. A sculptor in nitrile ships a sealed SLA; a fulfillment center re-bags it with latex and a powdered sheet. Our receiving note asks for glove polymer. If nobody answers, we treat it as unknown and slug before the production cup. That slug is not billed as a personality test — it is how we keep a food well off a tacky face.

Skin-safe claims on a *dump* (a mask, a prop appliance) are not this page. Latex-free as a *costume* spec is a buyer document. Latex-free as a *bench glove* spec is ours. Do not mash them. We will not invent an ISO 10993 file because someone wore nitrile.

A tooling charge still does not mean unrestricted ownership of the master we recleaned. Write who stores it so the next inbound does not go back through latex.

Food path: a latex-handled well that failed is recast from a master handled in nitrile. Wash is not a cert. Keep latex boxes off the food tote entirely so a night shift cannot 'just grab a pair.' The same split we ask for food vs soap rags applies to glove dispensers.

Failure: packing peanuts and beige gloves

Symptom: buyer-sealed SLA, our slug tacky in fingerprints, control fine.

Cause: packing crew wore latex; powder in the letter counters.

Fix: clean, nitrile from here, slug again. If type will not quiet, $50 remodel. Do not pour "a little extra catalyst." Platinum is not a tin you can starve or flood that way on a food well.

Typical shop values

Caption: typical shop values, not a named PO.

Glove habits we would not recommend

We would not recommend latex on a platinum bench, powder-free or not.

We would not recommend washing a food master and skipping the second slug.

We would not recommend "just use tin" to survive latex on a chocolate well.

We would not recommend vinyl as a default without a coupon.

We would not recommend extra bake as a fingerprint repair.

Worked example: beige gloves on a chocolate bar print

SLA bar, 180 mm, packed by a 3PL in latex. First 20 g tacky in pad marks. Nitrile clean, second slug passed on a hidden land that matched the face, platinum 1:1 tray. Prototype 3–7 business days after CAD lock. No $50 CAD. Production MOQ 20 of that design. 3PL got a nitrile note on the next inbound.

Mix-up: any "rubber glove" is fine

Nitrile ≠ latex ≠ vinyl. A black nitrile cuff still needs to be nitrile, not a rebranded latex 'exam glove' from a mixed box. Read the dispenser. If the box says natural rubber latex, it does not belong on the platinum bench even if the buyer calls it a 'shop glove.' Related: SLA inhibition, contact.

What to ask when you're buying

• Who handled the master after print — which glove polymer?
• Powdered or powder-free (still tell us if latex)?
• May we slug before the production cup?
• Food well — recast if the slug fails?
• After lock, 3–7 business days, then MOQ 20 / design?

RFQ copy-pack — latex vs nitrile

Paste into [email protected]:

Object: platinum RTV mold, nitrile handling, not LSR Master: how it was packed and handled Dump: food or craft Slug a hidden land before the production cup File: photos + millimetre scale, or ship the master CAD: quiet master OR USD $50 3D if we remodel Prototype 3–7 business days after CAD lock, then MOQ 20 per design Who keeps the master

Send the glove story with the print, not "it's clean." We slug fingerprints — not a blank quote request. Phone +86 135 3006 2969. Xinhe Blvd, Shajing, Bao'an. Shop since 2018.

FAQ

Do latex gloves inhibit platinum silicone? Yes. Use nitrile on the platinum bench. Powder-free latex is still latex.

Can I wash the master after latex and pour? Clean, then a 20 g slug that represents the face. Do not skip the coupon on a food logo.

Is vinyl OK? Coupon it. Do not assume. Nitrile is the default we stock.

Will tin-cure ignore latex? Tin is a different chemistry and not a food workaround. Do not switch chocolate to tin to survive beige gloves.

Does this change lead time? CAD lock includes a quiet, nitrile-handled master. A fail is not locked. Clock is 3–7 business days after lock; MOQ 20 per design. Mix 1:1 or 10:1.